Refine your search
Collections
Journals
Year
A B C D E F G H I J K L M N O P Q R S T U V W X Y Z All
Priya, R.
- Corrosion Behaviour of SS304L at Unapproachable Regions of Fillet Weld Joints in Fast Reactor Reprocessing Application
Abstract Views :53 |
PDF Views:2
Authors
Affiliations
1 Indira Gandhi Centre for Atomic Research, Kalpakkam – 603 102, IN
1 Indira Gandhi Centre for Atomic Research, Kalpakkam – 603 102, IN
Source
Indian Welding Journal, Vol 56, No 4 (2023), Pagination: 46-53Abstract
The Purex process is opted for reprocessing of spent fuel from fast breeder reactors. The process employs nitric acid with concentrations up to 11M. Nitric Acid Grade (NAG) SS304L is opted as material of construction for equipments, process tanks and piping of such process plants so as to minimise the corrosion losses due to nitric acid. Practice C test as per ASTM A262-15(2021) (Standard Practices for Detecting Susceptibility to Intergrannular Attack in Austenitic Stainless Steels), with maximum average corrosion rate of 15 mils/year (mpy) for five cycles of 48 hrs, and 18 mpy in any cycle, is one of the criteria for qualification of material among others. A similar acceptance criterion is adopted for qualification of undiluted weld metal deposit of filler material and welding procedure specification (WPS) used therein. However, conventional tests may not always accurately represent the corrosion behaviour of surfaces at all locations. One of such are the surfaces which abut each other, and hence are not approachable for visual examination and thereafter cleaning, such as unwelded open abutted surfaces of fillet weld joint (root), partial penetration (pp) weld joints facing process fluids in abutted portions not in a welded portion of joint. Multiple factors like remains of heat tints, adjacent inter-spaces and type of surface finish may collectively contribute to corrosion rates exceeding acceptable limits. This study delves into the often-neglected corrosion behaviour of these challenging regions. The samples with abutting surfaces are prepared by using EDM cutting and and Gas tungsten arc welding (GTAW) and subjected to corrosion test. The samples made by using base material, filler and WPS that already qualified for corrosion test for groove weld joints and hence fillet weld joints as per ASME BPVC sec IX (2021). Higher corrosion rates are being observed in these weld joints than standard test specimens during study.Keywords
Abutting Surfaces, Heat Tint, Gas Tungsten Arc Welding, Huey Test.
References
- Sunil Kumar B, Kain V, Benerjee K, Maniyar PD, Sridhar S, Jitendra K and Jatin K (2013); Effect of oxidation on corrosion behaviour of austenitic stainless steel 304l welds, Advanced Materials Research, 794, pp.598-605.
- Brajkovi T, Juraga I and Šimunovi V (2013); Influence of surface treatment on corrosion resistance of Cr-Ni steel, Engineering Review, 33. pp.129-134.
- Tuthill A H (1999); Heat tints on stainless steels can cause corrosion problems, NIDI Materials Performance, pp.72-73.
- Bobic B, Jegdić B and Gligorijević B (2014); Analysis of corrosion damage in a boiler made of AISI 304L stainless steel, Zastita Materijala, 55, broj 1.
- Somervuori M and Johansson HLS, Hoecke M, Akdut D, Hänninen N, Hannu (2004); Characterisation and corrosion of spot welds of austenitic stainless steels, Materials and Corrosion, 55, pp.421-436.
- Sunil Kumar B (2013); Effect of oxidation on corrosion behaviour of austenitic stainless steel 304l welds, Advanced Materials Research, 794, pp.598-605.
- Robert B (Ed) (2005); ASTM, Corrosion Tests and Standards: Application and Interpretation Sec. Ed. p.246.
- ASTMA262-15(2021); Standard Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels, ASTM.
- Brown M (1974); Behavior of austenitic stainless steels in evaluation tests for the detection of susceptibility to intergrannular corrosion, Corrosion, 30, NACE, pp.2-3.
- Tripathi SK, Kuppusamy MV and Athmalingam S (2022); Qualification of critical weld joints for dynamically balanced nuclear component, Indian Welding Journal, 55, pp.54-62.
- Natarajan R and Raj B (2011); Fast reactor fuel reprocessing technology: successes and challenges, Asian nuclear prospects 2010, Energy Procedia, 7, pp.414–420.
- Raj B and Mudali U K (2006); Materials development and corrosion problems in nuclear fuel reprocessing plants, Progress in Nuclear Energy, 48(4), pp.283-313.
- Fauvet P (2012); Corrosion issues in nuclear fuel reprocessing plants, Nuclear Corrosion Science and Engineering, pp.679-728.
- Khan S and Hussain M (2020); Corrosion behaviour of 304L NAG and 310L NAG in nitric acid, Investigation of Causes and Preventive Steps, pp.1-9.
- SFA 5.9, Section II Part C, Boiler and pressure vessel code (2021); ASME, pp.277-303.
- QW 451.4 (2021), Sec IX, Boiler and pressure vessel code ASME (2021), p.205.
- A380/A380M, Standard Practice for Cleaning, Descaling, and Passivation of Stainless Steel Parts, Equipment, and Systems (2017), ASTM.
- Kelly RG (2003); Crevice Corrosion, Corrosion: Fundamentals, Testing, and Protection, Vol 13A, ASM Handbook, ASM International, pp.242–247.
- Fontana MG (2017); Corrosion Engineering, 3rd Edition, p.58.